Setting New Standards

RF & Microwave T-Matched Pick-Off Tees

TAYLOR MICROWAVE, INC.  |  RF & MICROWAVE

T-Matched Pick-Off Tees

Low-loss stripline pick-off tees for RF and microwave signal monitoring.

Taylor Microwave pick-off tee with J1 and J2 through ports and a J3 tap marked −20.5 dB
J3 tap marked −20.5 dB

High-Performance Pick-Off Tees

Taylor Microwave T-Matched Pick-Off Tees are low-cost, high-performance stripline devices
designed to provide a controlled RF pick-off signal while maintaining low insertion loss
and repeatable performance. Standard models are available for broadband RF and microwave
applications, with custom frequency bands and electrical specifications available.

DC–40 GHz
Broadband Frequency Coverage

Low Loss
Efficient RF Signal Coupling

Repeatable
Consistent Performance

Custom
Frequency & Connector Options

T-Matched Pick-Off Tee Configurations

Taylor Microwave offers several T-matched Pick-Off Tee configurations to meet different RF matching and pick-off requirements.

Taylor Microwave T-Matched Pick-Off Tee Schematics

Pick-Off Tee

No Matching

Pick-Off Tee

J1 Matched

Pick-Off Tee

J1 / J2 Matched

*R3 is optional for matching J3.

POT-XXG SMA Series

Standard SMA Pick-Off Tee models are available for broadband RF and microwave applications.
Custom frequency bands and electrical specifications are also available.

Pick-Off Tees
No Match
P/N
(1)
Frequency
Range
(GHz)
Insertion
Loss
Max. (db)
(2)
Pick-Off (db)
VSWR
IN/OUT
Max.
(3)
Input
Power
(Watts Max.)
R2 (Ohms)
POT-XXGUser Defined
Contact TMI
User Defined
Contact TMI
User Defined
Contact TMI
POT-20G-11DC-201.810.9 +/-11.7/1.71100
POT-20G-20DC-201.119.6 +/-11.5/1.51400
POT-20G-15DC-201.214.5 +/- 11.5/1.51200
POT-30G-15DC-301.215 +/- 11.6/1.61200
POT-40G-15DC-402.515 +/- 1.251.5/1.51200

J1 / J2 Matched Pick-Off Tees

Matched J1/J2 models provide controlled pick-off performance with matched main-line ports
for demanding RF and microwave applications.

Pick-Off Tees
J1/J2 Matched
P/N
(1)
Frequency
Range
(GHz)
Insertion
Loss
Max. (db)
(2)
Pick-Off (db)
VSWR
IN/OUT
Max.
(3)
Input
Power
(Watts Max.)
R1 (Ohms)R2 (Ohms)
POT-XXGUser Defined
Contact TMI
User Defined
Contact TMI
User Defined
Contact TMI
User Defined
Contact TMI
User Defined
Contact TMI
POT-26G-15ADC-263.114.9 +/-1.251.5/1.50.5005200
POT-26G-20ADC-262.520.5 +/-2.01.5/1.50.5002.5400

POT-F Series — 75 Ohm Pick-Off Tees

The POT-F Series provides 75-ohm pick-off tee configurations for broadband applications through 3 GHz.

Pick-Off Tees
P/N
(1)
Frequency
Range
(GHz)
Insertion
Loss
Max. (db)
(2)
Pick-Off (db)
VSWR
IN/OUT
Max.
(3)
Input
Power
(Watts Max.)
R1 (Ohms)
POT-XXGUser Defined
Contact TMI
User Defined
Contact TMI
User Defined
Contact TMI
POT-15-FDC-3.01.115 +/- 0.501.25/1.251300
POT-20-FDC-3.00.7019.5 +/- 0.501.15/1.151600

Taylor Sense-Tee for Bias Voltage Sensing

The Taylor Sense-Tee samples the voltage on a 50 Ω RF line through
a series pick-off resistor. Connect J1 to the bias tee’s RF+DC output
and J2 to the device under test. Connect J3 to a
50 Ω oscilloscope input or a 10 MΩ voltmeter. Use a DC-coupled oscilloscope
input to measure DC bias.

Voltage Scaling at J3

The pick-off resistor and the instrument’s input resistance form a voltage divider.
Multiply the measured voltage by the scale factor k to calculate the voltage at the tap.


Rpick-off = (k − 1) Rinput


k =


Vtap


Vmeasured


  • 50 Ω oscilloscope input.
    A 2 kΩ pick-off resistor gives a 41:1 voltage ratio.
    For a 10:1 ratio, use a 450 Ω pick-off resistor.
  • 10 MΩ voltmeter.
    A 2 kΩ pick-off resistor gives a DC scale factor of 1.0002.
    A 5.000 V tap voltage reads approximately 4.999 V before accounting for meter accuracy.

ST-A01 uses a 3 kΩ pick-off resistor.
Its nominal resistive divider ratio is 61:1 with a 50 Ω input,
and its DC scale factor is 1.0003 with a 10 MΩ voltmeter.

The 10 MΩ value applies to DC. For RF and fast pulses, the instrument’s input
capacitance and the test connection also affect the measured voltage.


P/N
Frequency
Range
(GHz)
Insertion
Loss
Max. (db)

Pick-Off (db)
VSWR
IN/OUT
Max.

Input
Power
(Watts Max.)
R1 (Ohms)
ST-AXXDC-20X.XXXX.XXX.XX/X.XXXXXXXX
ST-A01DC-201.0>301.25/1.25103000

Please specify your frequency range, DC voltage, current, and voltage-sensing requirements.

Custom Pick-Off Tee Designs

Taylor Microwave can provide custom frequency bands and optimized electrical specifications
to meet your application requirements.

  • Custom frequency ranges
  • Custom pick-off values
  • Optimized insertion loss and VSWR
  • High-power configurations
  • Custom connector configurations
  • Custom stripline designs

Need a Custom Pick-Off Tee?

Contact Taylor Microwave for custom frequency bands, pick-off values, power levels,
connectors, and optimized specifications.


Get a Product Quote